RE: IML: Problem with 1960 Imperial door solenoid (electric door lock)

["Rob van der Es" <r.vdes@xxxxxxxxxxxxxxx>]

Great John,

Thanks a lot for your kind suggestions, I will contact those guys right away!



Op Ma, 24 juli, 2006 5:26 am, schreef Isenhour:
> I would think the guy at Imperial Heaven junkyard in NE could pull you
> one off of his many '60's sitting there waiting for a new home. I just got
> a few parts from him and had no problems. There are other Imperial junk
> yards too listed here like Dr. Mopar in TX orDesert Valley Yard in AZ
>
>
> -----Original Message-----
> From: mailing-list-owner@xxxxxxxxxxxxxxxx
> [mailto:mailing-list-owner@xxxxxxxxxxxxxxxx] On Behalf Of Rob van der Es
> Sent: Sunday, July 23, 2006 3:52 PM
> To: mailing-list@xxxxxxxxxxxxxxxx
> Subject: Re: IML: Problem with 1960 Imperial door solenoid (electric door
> lock)
>
> OK John,
>
>
> Thanks a lot, I will have a sharp eye on Ebay then for 60-63 parts !
>
>
> All the best,
>
>
> Robert
>
>
>
> Op Zo, 23 juli, 2006 10:49 am, schreef john sadowski:
>
>> Someone had a couple for sale on eBay recently. They are the same for
>> 60-63,
>> So you should be able to get another one fairly easy.
>> ----- Original Message -----
>> From: "Rob van der Es" <r.vdes@xxxxxxxxxxxxxxx>
>> To: <mailing-list@xxxxxxxxxxxxxxxx>
>> Sent: Sunday, July 23, 2006 12:04 AM
>> Subject: IML: Problem with 1960 Imperial door solenoid (electric door
>> lock)
>>
>>
>>> In addition to my previous question:
>>>
>>>
>>>
>>> Is it possible to open such a solenoid and to repair the problem that
>>> I
>>> described? Right now I have it in my hands but I can't see how to open
>>>  it..
>>>
>>> Thanks in advance,
>>>
>>>
>>>
>>> Robert
>>>
>>>
>>>
>>>
>>>
>>> Hello fellow club members,
>>>
>>>
>>>
>>> I have a question for all the 1960 experts (and problably other years
>>>  too) on the IML.
>>>
>>> My 1960 Crown has an electric door locking system, all the door locks
>>>  are controlled by a very powerful solenoid. One of the solenoids has
>>> a problem (front passenger door).. The outgoing stroke of the solenoid
>>> is too long, the operating  lever goes out too far for just 1/16 " or
>>> so when I give the command to close all doors. If that happens, the
>>> solenoid is locked somehow internally and the lever won't come in
>>> again if reverse power is supplied by the locking switch.
>>>
>>> Is it possible to correct the outgoing stroke of the solenoid?
>>> Or if not, does anyone on the IML has a spare one on the shelf that I
>>> can buy?
>>>
>>> Thanks in advance,
>>>
>>>
>>>
>>> Robert
>>>
>>>
>>>
>>>
>>>
>>>
>>> -----------------  http://www.imperialclub.com  -----------------
>>> This message was sent to you by the Imperial Mailing List. Please
>>> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
>>> shared with everyone. Private messages (and attachments) for the
>>> Administrators
>>> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
>>> http://imperialclub.com/unsubscribe.htm
>>>
>>>
>>>
>>>
>>
>>
>>
>>
>> -----------------  http://www.imperialclub.com  -----------------
>> This message was sent to you by the Imperial Mailing List. Please
>> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
>> with everyone. Private messages (and attachments) for the
>> Administrators
>> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
>> http://imperialclub.com/unsubscribe.htm
>>
>>
>>
>>
>
>
>
>
> -----------------  http://www.imperialclub.com  -----------------
> This message was sent to you by the Imperial Mailing List. Please
> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
> with everyone. Private messages (and attachments) for the Administrators
> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
> http://imperialclub.com/unsubscribe.htm
>
>
>
>
>
>
> -----------------  http://www.imperialclub.com  -----------------
> This message was sent to you by the Imperial Mailing List. Please
> reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
> with everyone. Private messages (and attachments) for the Administrators
> should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
> http://imperialclub.com/unsubscribe.htm
>
>
>




-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please 
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be 
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm